6X 22MM BMW DIESEL SWIRL FLAP BLANKS FLAPS REPAIR WITH INTAKE MANIFOLD GASKETS PART NUMBER: X8R66-X8R24
PRODUCT DESCRIPTION
Our repair kit in this listing addresses the common failure of the BMW swirl flap butterfly valves located within the intake manifold. Our components described herein with the assistance of our supportive instruction media will allow you to replace just the faulty components which always fail within the manifold. An extremely common fault corrected by our repair kit.
THE PROBLEM
SWIRL FLAPS WITHIN YOUR ENGINE DETERIORATE OVER TIME AND CAN END THE LIFE OF YOUR ENGINE!
As depicted above within the intake manifold of your BMW you will find these little blighters referred to as Swirl Flaps. Designed to produce a swirl of air to aid combustion when the engine is under light load; the flaps are held in place by two screws, unfortunately as the swirls move over time these screws can loosen or the spindle making their way in to your engine. This in-turn can do a number of things; jam open the valve port causing the piston to collide with the valve, enter the cylinder itself ending the life of the engine and even after leaving the engine further damage can be caused to the exhaust system.
THE SOLUTION
INSTALL OUR SWIRL FLAP BLANKS AND REST IN THE KNOWLEDGE THAT YOUR ENGINE IS SAFE
Remove the risk of your car being written off by the swirl flaps, remove the swirl flaps (our product comes with full instructions showing how to do this, others don’t offer this) and install our blanking plates. Our blanking plates directly swap with your existing swirl flaps, simply push in and screw in place. And the best bit is you will notice no difference in performance from you vehicle, you may even notice an improvement if your swirl flaps have deteriorated
VEHICLES AFFECTED
BMW engine codes and models:
M47N/M47TU/M47TUD20
E46 320d 2001-2005, E83 X3 2.0d (up to end of 2006)
M47TU2D20 updated in 2004 to M47TU2D20
E60/E61 520d, E87 120d, E90/E91 320d, E83 X3 2.0d - end of 2006 onwards
Previous M57 - 2000 onwards M57D25
2000-2003 E39 525d automatic transmission only.
M57N/M57TU - 2004 onwards M57TUD25
E60/E61 525d
M57/M57D29 - 1998 onwards M57D30
E39 530d automatic transmission only
E46 330d/330xd automatic transmission only
E38 730d automatic transmission only
E53 X5 3.0d, E38 730d, E39 530d
M57N/M57TU - 2002 onwards M57TUD30
E46 330d/330Cd/330xd
E83 X3 3.0d
E53 X5 3.0d
E60/E61 530d/530xd
E65 730d
E60/E61 535d
M57TU2D30 M57TU2D30 - 2007 onwards, facelifted E60 and E61
M57TU2D30-UL M57TU2D30-OL M57TU2D30-TOP
E90/E91/E92 325d
E60/E61 525d/525xd E65 730d
E90/E91 325d
E90/E91 330d/330xd
E60/E61
BMW E70
BMW E71
E60/E61 535d
E70 X5 3.0sd
E71 X6 xDrive35d
E83 X3 3.0sd
E90/E91 335d
WHICH SIZE DO I NEED 22MM OR 33MM?
Our Swirl Flap blanks are available in 22mm and 33mm size (some refer to 33mm as 32mm they are the same thing). Unfortunately it is difficult to determine which size swirl flaps your vehicle has fitted and as such which size blanks you require. As a rule of thumb but far from guaranteed 22mm tend to be fitted on vehicles up to 2004, 2004-2006 either size can be fitted and 2006 on 33mm size. However over the years many exceptions have been found and BMW do not hold data as to which are fitted to your vehicle. We therefore advise measuring the swirl flaps in your manifold or ordering a set of both size and returning the unused set for refund, this is what most of our customers choose.
YOU WILL RECEIVE
You will receive:
6 x 22mm Swirl Flap blanks and
1x 11612245439 Manifold gasket between the AGR valve and the intake manifold.
6x 11612246945 Intake manifold gaskets upper against the cylinder head cover.
6x 11617790198 Intake manifold gaskets lower against the cylinder head.
All gaskets are sourced from Elring or Reinz, not poor quality copys which will fail.
For other size swirl flaps or to order without the manifold gaskets please visit our eBay store.
Precision machined to the finest tolerances for the perfect fit, maintaining that all important air tight fit. Billet aluminium, so no joints to go wrong, made out of one solid piece of metal! Fitted with a high quality Viton seal. Beware of poor quality rubber 0-rings that other sellers offer, these will not last in the manifold with the elevated temperatures and prolonged exposure to fuel.
