SYMPTOMS OF FAULT
Poor MPG, rough idle, boost loss, check engine light, sluggish performance, significant power losses, poor drivability. Oil leaking from oil cap, oil in the engine bay, PCV pipe work leaking, boost / vac leaks.
THE PROBLEM
A DIAPHRAGM SPLITS OR DETERIORATES WITHIN THE PCV UNIT CAUSING VEHICLE FAULTS.
One of the most common faults on the 2.0 TFSI engine is the failure of the pressure control valve (PCV). This valve is designed to recirculate crankcase gases into the intake manifold. Within the valve is a soft diaphragm which is prone to splitting over time, this can occur on stock engines but is very common on tuned engines.
This results in excessive blow by entering the inlet manifold at idle causing oil leaks in the engine bay from crankcase pressure, rough idle, fuel economy decline and boost loss. With boost pressure below where it should be you will notice significant power losses and poor throttle response. Check our symptoms section to see common symptoms of the failure of this valve.
THE SOLUTION
INSTALL OUR PCV DELETE UNIT AND RESTORE PERFORMANCE TO YOUR VEHICLE, REMOVING THE POOR-QUALITY COMPONENT THAT COMMONLY FAILS.
Our replacement unit installs very easily and quickly. Upon fitting you will notice a vast improvement in performance and power if your OEM PCV has failed.
Our beautifully machined billet anodised aluminium unit (check our feedback for the quality of our manufacturing). Directly replaces the PCV unit deleting the OEM PCV system. Removing the original flawed design part from the engine.
Our unit links the two internal ports together, this emulates what happens inside the OEM PCV when the engine is on boost, but removes the fragile components which commonly fail.
Our unit converts the system to a vacuum only based system. PCV function is properly retained and no emissions functions are effected with our unit.
Our kit also includes a blank for the inlet manifold. This is engineered with three ports, where either our vacuum nipples can be fitted (included in kit) to run a boost gauge or water spray controller or these can be blanked off (blanks included).
Install our kit and restore full performance to your vehicle, engineered to last the life of the vehicle.
VEHICLES AFFECTED
VEHICLES AFFECTED AND PART NUMBERS
COMPATIBLE WITH TIMING BELT-DRIVEN 2.0 TFSI ENGINES.
AUDI A1 2.0 TFSI, CDLH ENGINES. 2011 TO 2013.
AUDI A3 (8P) 2.0 TFSI, AXX, BPY, BWA, CCZA, CDLA, BHZ, ENGINES. 2004–2013.
AUDI S3 (8P) 2.0 TFSI BHZ, CDLA ENGINES. 2006–2013.
AUDI A4 B7 2.0 TFSI 2005-2008.
AUDI TT 2.0 TFSI & 2.0 TTS BWA, AXX, BPY, CDLA, CDLC, ENGINES. 2007 TO 2013.
SEAT LEON COPA 2.0 TFSI 2008 ONWARDS.
SEAT LEON 2.0 TFSI CCZB, CAWB ENGINES. 2009 ONWARDS.
VW 2.0 LITRE TFSI ENGINES. BELT CAM EA113 ENGINE:
VW GOLF MK5 GTI 200BHP 2004-2006.
VW GOLF MK5 EDITION 30 2007-2010.
VW GOLF MK6 EDITION 35.
VW GOLF MK6 GOLF R.
VW SCIROCCO MK3 R 2.0 FSI EA113 2009 ONWARDS.
VW PASSAT B6 2.0 TFSI AXX, BWA ENGINES. 2005-2007.
SKODA OCTAVIA MK2 2.0 TFSI VRS. BWA ENGINE. 2005-2008.
INFORMATION IS FOR GUIDANCE ONLY, IT IS WORTHWHILE CHECKING THE INTAKE MANIFOLD TO ENSURE YOUR VEHICLE HAS A PCV VALVE AS ILLUSTRATED IN THE LISTING.
ASSOCIATED PART NUMBERS:
06F129101N, 06F129101C, 06F129101E, 06F129101F, 06F129101K, 06F129101L, 06F129101R,
IF UNSURE CALL OR E-MAIL AND WE CAN LOOK UP YOUR VEHICLE.
YOU WILL RECEIVE
Billet Black Anodised Aluminium Valve Cover Plate
Billet Silver Anodised Aluminium PCV Adapter
Billet Silver Anodised Aluminium Manifold Cap
High quality Viton O-Rings To Provide Seal Between Components
OEM Retaining Clip
Vacuum Nipples X3
Blanking Screws X3 (for use in place of vacuum nipples)
